Mgcamd-Kristen Stewart

[Kristen Stewart]

thank's but nothing work i thing my line is off from the server but is ok

how can you say that ?
you can verify your line status at = http://www.testious.com/" onclick="window.open(this.href);return false;

[notari]

thank's but nothing work i thing my line is off from the server but is ok

how can you say that ?
you can verify your line status at = http://www.testious.com/" onclick="window.open(this.href);return false;

dear but i try evrything and my line not work if is ok but i have problem and for me not work

[Masood]

@notari
plz share your problem, we are here to find out solutions.

@mgcamd
login is very fast

[notari]

@notari
plz share your problem, we are here to find out solutions.

@mgcamd
login is very fast

my friend here is my mgcamd 1.38( http://www.4shared.com/folder/ioO9h70x/_online.html" onclick="window.open(this.href);return false; )i don't now what happen if somebody want to help

[ayanahmed]

1- Valuable advice:

If you are going to use SoftCam.Key file for certain channels and sharing server - for other channels, be sure that there is NO KEYS in the SoftCam.Key for the channels you are going to open using sharing server. mgcamd is always looking for the keys into the SoftCam.Key and if the key is found (even old one and not working), it will use only it. Naturally, that if the key is old and is not working, you will see a black screen even if you have connection to the sharing server. Therefore, it is recommended to delete SoftCam.Key from /var/keys (or rename it to the file with other extension), set up the remaining things, be sure that everything works properly, and then to decide if you need SoftCam in further sharing.

2- By default, the settings of mg_cfg file are as follows:

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 02 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 360 3600

# network ecm timeout in seconds
K: { 07 }

# newcamd dead routes connect retry, sec
Q: { 60 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 02 } root password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log
#The line L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log means IP of your PC (replace 192.168.1.1 with your computer IP #address in the network, 28007 - is a port to communicate btw receiver and PC - don't change!).

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 00 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 31 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
#For firmware on DGS basis (Ab-com, NLB, SifTeam, PGI, UFM), parameter B: { 12 }
#For Enigma firmware, B: { 11 }
B: { 00 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

[notari]

friend i am not use softcam.key and i var.key have just this file i post and i am using openpli 4

[ayanahmed]

Your box type

& Mg_Cfg

[notari]

Your box type

& Mg_Cfg

my box is sunray4

[Pirat3]

Your box type

& Mg_Cfg

my box is sunray4

@ notari

I think it's about MGCamd, I have OplenPli 4.0 and had same issue until I install this version

[code]https://www.dropbox.com/s/uv7sh2ny4kyox ... ar.gz?dl=0[/code]

Well....uninstall your current version, download this file, and install it in your box.

[haroongouri]

thanks to email.
only one sentence in that.
sorry you have only 10 post.
whats this?????