Experts help needed in Power Vu Channels on E2
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
Experts help needed in Power Vu Channels on E2
I just saw this option and don`t know what it does. Can someone tell me what does it mean?
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
Experts help needed in Power Vu Channels on E2
Code: Select all
This is my dvbapi configuration. Is something wrong with this?
##############################
# dvbapi configuration #
##############################
# types:
# P - Priority
# format:
# P: <caid>:[<provider>]:[<srvid>]:[<ecmpid>]
# I - Ignore
# format:
# I: <caid>:[<provider>]:[<srvid>]:[<ecmpid>]
# M - Map
# format:
# M: <caid>:[<provider>]:[<srvid>]:[<ecmpid>] <target caid>:[<target provider>]
# D - Delay
# format:
# D: <caid>:[<provider>]:[<srvid>]:[<ecmpid>] <delay (ms)>
#
#
#
P: 0100:000068 # nC+
P: 1803 # Polsat
#I: 0 # ignoruj inne caid
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
Experts help needed in Power Vu Channels on E2
In the configuration of Oscam Web IF which mode shall I use?
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
Experts help needed in Power Vu Channels on E2
Anyone that can help???
How to install the drivers that joeuser has provided -> HDMU_16560_E2_spark_217_git_581 + HW DES Drivers in Open ATV 6.0 in sh4 type receivers for 7162 chip???
I tried the method joeuser stated above but it crashed my image. Any other method to put these drivers in my image???
Thanks in advance...
After changing the files and restarting the receiver it is stuck in a continuous loop it loads to 100% then again comes to 50% and loads back to 100% and comes back to 50% and on and on...
This method didn`t work. What Should I do now?
How to install the drivers that joeuser has provided -> HDMU_16560_E2_spark_217_git_581 + HW DES Drivers in Open ATV 6.0 in sh4 type receivers for 7162 chip???
I tried the method joeuser stated above but it crashed my image. Any other method to put these drivers in my image???
Thanks in advance...
After changing the files and restarting the receiver it is stuck in a continuous loop it loads to 100% then again comes to 50% and loads back to 100% and comes back to 50% and on and on...
This method didn`t work. What Should I do now?
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
Experts help needed in Power Vu Channels on E2
Believe me this is the maximum that I can go. I`ve exhausted every possible option that "I" in my little and limited knowledge had.
Now it is up to the experts and this whole forum to put all your experience, knowledge and expertise together and save the day.
I look forward to all your help because without it I can`t proceed even an inch. So kindly detect the problem here, help me so that this thread can be closed and that I can take a sigh of relief.
If anyone of you need any kind of info about my settings in public or in private let me know.
If my oscam emulator is finding the key as highlighted in red in the log below. Why doesn`t the picture come of the channel?
2017/07/06 11:18:05 1D942ADA c (ecm) linuxsatsupport (0E00@000000/0000/0002/40:D2973E9AD4BA179684422502911B319A): found (11 ms) by oscam_emu (L/1/7/7) - AtlanticP 1F86 00 3581B4C2D46026 ;7W 11595
Now it is up to the experts and this whole forum to put all your experience, knowledge and expertise together and save the day.
I look forward to all your help because without it I can`t proceed even an inch. So kindly detect the problem here, help me so that this thread can be closed and that I can take a sigh of relief.
If anyone of you need any kind of info about my settings in public or in private let me know.
If my oscam emulator is finding the key as highlighted in red in the log below. Why doesn`t the picture come of the channel?
2017/07/06 11:18:05 1D942ADA c (ecm) linuxsatsupport (0E00@000000/0000/0002/40:D2973E9AD4BA179684422502911B319A): found (11 ms) by oscam_emu (L/1/7/7) - AtlanticP 1F86 00 3581B4C2D46026 ;7W 11595
- abdullahkhan.007
- Registered Member
- Posts: 466
- Joined: 07 Jan 2015, 8:51 pm
- Has thanked: 44 times
- Been thanked: 10 times
- Contact:
Experts help needed in Power Vu Channels on E2
If this method words, kindly can someone post a screenshot of any channel that they have enabled by stream relay method either over here or pm me.
Because, I think that this so called "Stream Relay Method" is a failed experiment by engineer khan. And I highly doubt this method until someone prove me wrong.
Because, I think that this so called "Stream Relay Method" is a failed experiment by engineer khan. And I highly doubt this method until someone prove me wrong.
Who is online
Users browsing this forum: Ahrefs [Bot], Apple, Bing, Google Adsense and 210 guests