Respected Experts . i have done seething of 10 satellite so i want to know how connect all theses on one receiver every one knows in Pakistan easily available 4X1 Disqc switch also 8x1 switch is available both i have used .. now i have ten inputs and it may increase so kindly tell me the easily available solution in pakistan . and please guide me properly i have spend more than three days on net but unable to find any proper solution every one have there own solution without any reference. So Please please i need only experts opinion and solution... i ma so much tens after so much search and double minded so kindly provide me the cheap solution ...
Waiting Quick response form Experts ..
Regards,
Raiyan
Need experts opinion related diseq switch- Really Urgent Pleazz
- Athart
- Vip
- Posts: 3722
- Joined: 21 Mar 2017, 1:00 pm
- Has thanked: 991 times
- Been thanked: 2328 times
Need experts opinion related diseq switch- Really Urgent Pleazz
EuroBird, HotBird, EuTel 16A, Badr, PakSat, TurkSat, Turkmen/YahSat-1
DM520, SRT2020+, T800, Sony 40W660E, Sony 24EX430
DM520, SRT2020+, T800, Sony 40W660E, Sony 24EX430
Need experts opinion related diseq switch- Really Urgent Pleazz
You can utilize 32 LNBs by this setup. A little explanation to understand the receiver installation menu is here.adnan_85 wrote: ↑29 Aug 2017, 10:26 am Respected Experts . i have done seething of 10 satellite so i want to know how connect all theses on one receiver every one knows in Pakistan easily available 4X1 Disqc switch also 8x1 switch is available both i have used .. now i have ten inputs and it may increase so kindly tell me the easily available solution in pakistan . and please guide me properly i have spend more than three days on net but unable to find any proper solution every one have there own solution without any reference. So Please please i need only experts opinion and solution... i ma so much tens after so much search and double minded so kindly provide me the cheap solution ...
Waiting Quick response form Experts ..
Regards,
Raiyan
Diseqc1.0 setting is for 4ports switch and Diseqc1.1 setting is for 8ports switch.
Lets consider this situation if Diseqc1.0 setting shows LNB1, then it's mean that the 4pin Dieqc switch makes path to output port1, similerly if Diseqc1.1 setting shows LNB5, the 8pin Diseqc switch make path to it's port5.
Now keeping above setting if we connect 4port switch after the 8port switch then from the above setting this path sequence is formed ( Receiver -> Diseqc8-port5 -> Diseqc4-port1 -> LNB ).
And if we connect 8port switch after the 4port switch then the path is as follows ( Receiver -> Diseqc4-port1 -> Diseqc8-port5 -> LNB ).
As you can see each Diseqc switch respond only to it's dedicated command.This mean we cannot use two Diseqc switches of the same type in cascade mode ( yani aage peche ), because they'll both acts to the same command.
Further to make reliable connection,, Commands for Diseqc switches are sent multiple times by Receiver in order to arrive at the final switch in the cascade.
-
- Registered Member
- Posts: 91
- Joined: 01 Mar 2016, 2:13 pm
- Has thanked: 2 times
- Been thanked: 2 times
Need experts opinion related diseq switch- Really Urgent Pleazz
@Chazer Thank you so much for your reply
I am little bit confused .. i try to explain my current setting .
Dish seething..
currently i have three diseq switches 4x1 . I am using two for 8 LNB connect and other one two ports are connect with these switch and other two ports are directly connect to lnb then connect to receiver ... See attachment ..
Receiver seething..
In satellite installation session there are three list
1. if select the diseq 1.0 then below appear only one selection list which having values A,B,C,D .. every one knows this setting
2. 1. if select the diseq 1.1 then below appear two selection list first having values A,B,C,D ..and third show number 1 to 16
my problem is i can get only those LNS signal on receiver which are directly connect to diseq 3 ... other two diseq signal not show ..
i already try below
List one "diseq 1.1"
List two "A" - here diseq 1 is connected
List three "1" - select 1 to 4 as per need
But i can not get any signal even not get strength signal
same seething wrsks fine with directly connect LNB..
I hope you understand my issue .. kindly share your contact cell or whats app if possible .. waiting your response.
I am little bit confused .. i try to explain my current setting .
Dish seething..
currently i have three diseq switches 4x1 . I am using two for 8 LNB connect and other one two ports are connect with these switch and other two ports are directly connect to lnb then connect to receiver ... See attachment ..
Receiver seething..
In satellite installation session there are three list
1. if select the diseq 1.0 then below appear only one selection list which having values A,B,C,D .. every one knows this setting
2. 1. if select the diseq 1.1 then below appear two selection list first having values A,B,C,D ..and third show number 1 to 16
my problem is i can get only those LNS signal on receiver which are directly connect to diseq 3 ... other two diseq signal not show ..
i already try below
List one "diseq 1.1"
List two "A" - here diseq 1 is connected
List three "1" - select 1 to 4 as per need
But i can not get any signal even not get strength signal
same seething wrsks fine with directly connect LNB..
I hope you understand my issue .. kindly share your contact cell or whats app if possible .. waiting your response.
-
- Senior Registered Member
- Posts: 734
- Joined: 08 Nov 2014, 5:50 pm
- Location: Lahore, Pakistan
- Has thanked: 1 time
- Been thanked: 41 times
Need experts opinion related diseq switch- Really Urgent Pleazz
Yes it works this way I am using one 8 pin and second 4 pin disque switch to view 10 satellites, 1st 4ft Dish with105e-Cband, 100e-Kuband, 95e Kuband, 88e-Kuband & Abs2a @ 74.5e Kuband, 2nd 2ft dish with 52e Yahsat, 42e Turksat, and 36e Eutelsat 36b all Kuband and 3rd Dish old 8ft Mesh with Paksat 38e Cband centre & 49e Yamal 202 Cband
- awan71
- Gold Contributor
- Posts: 1833
- Joined: 11 Dec 2013, 1:32 am
- Location: Multan,Pakistan.
- Has thanked: 417 times
- Been thanked: 442 times
Need experts opinion related diseq switch- Really Urgent Pleazz
Dear adnan85
In this method you have select the correct command order on your receiver such as shown in pic.
This is my SRT 2020 HD receiver's setting I am using one 8 pin DiSEq & one 4pin DiESq swithes .
You May get some help by this diagram.
In this method you have select the correct command order on your receiver such as shown in pic.
This is my SRT 2020 HD receiver's setting I am using one 8 pin DiSEq & one 4pin DiESq swithes .
You May get some help by this diagram.
New. ZGEMMA H7s,
Tiger T3000 Mega,
StarSat SR-90000 HD EXTREME,
SRT 2020 Hd +,
Samsung 5 series l 5000 40, Samsung 49 NU 7100 UHD(4K),
Samsung A 6+, Samsung galaxy A20s ,
Sony HDR-CX160E ,Nikkon D 3400 DSLR .
Tiger T3000 Mega,
StarSat SR-90000 HD EXTREME,
SRT 2020 Hd +,
Samsung 5 series l 5000 40, Samsung 49 NU 7100 UHD(4K),
Samsung A 6+, Samsung galaxy A20s ,
Sony HDR-CX160E ,Nikkon D 3400 DSLR .
- Athart
- Vip
- Posts: 3722
- Joined: 21 Mar 2017, 1:00 pm
- Has thanked: 991 times
- Been thanked: 2328 times
Need experts opinion related diseq switch- Really Urgent Pleazz
If you upload Diseq setting pic, then it would be great.bilalpk wrote: ↑30 Aug 2017, 3:20 pm Yes it works this way I am using one 8 pin and second 4 pin disque switch to view 10 satellites, 1st 4ft Dish with105e-Cband, 100e-Kuband, 95e Kuband, 88e-Kuband & Abs2a @ 74.5e Kuband, 2nd 2ft dish with 52e Yahsat, 42e Turksat, and 36e Eutelsat 36b all Kuband and 3rd Dish old 8ft Mesh with Paksat 38e Cband centre & 49e Yamal 202 Cband
EuroBird, HotBird, EuTel 16A, Badr, PakSat, TurkSat, Turkmen/YahSat-1
DM520, SRT2020+, T800, Sony 40W660E, Sony 24EX430
DM520, SRT2020+, T800, Sony 40W660E, Sony 24EX430
- awan71
- Gold Contributor
- Posts: 1833
- Joined: 11 Dec 2013, 1:32 am
- Location: Multan,Pakistan.
- Has thanked: 417 times
- Been thanked: 442 times
Need experts opinion related diseq switch- Really Urgent Pleazz
This is my Current Setting for 9 Lnbs.
Regards.
Regards.
New. ZGEMMA H7s,
Tiger T3000 Mega,
StarSat SR-90000 HD EXTREME,
SRT 2020 Hd +,
Samsung 5 series l 5000 40, Samsung 49 NU 7100 UHD(4K),
Samsung A 6+, Samsung galaxy A20s ,
Sony HDR-CX160E ,Nikkon D 3400 DSLR .
Tiger T3000 Mega,
StarSat SR-90000 HD EXTREME,
SRT 2020 Hd +,
Samsung 5 series l 5000 40, Samsung 49 NU 7100 UHD(4K),
Samsung A 6+, Samsung galaxy A20s ,
Sony HDR-CX160E ,Nikkon D 3400 DSLR .
Need experts opinion related diseq switch- Really Urgent Pleazz
adnan_85 wrote: ↑30 Aug 2017, 12:21 pm @Chazer Thank you so much for your reply
I am little bit confused .. i try to explain my current setting .
Dish seething..
currently i have three diseq switches 4x1 . I am using two for 8 LNB connect and other one two ports are connect with these switch and other two ports are directly connect to lnb then connect to receiver ... See attachment ..
Receiver seething..
In satellite installation session there are three list
1. if select the diseq 1.0 then below appear only one selection list which having values A,B,C,D .. every one knows this setting
2. 1. if select the diseq 1.1 then below appear two selection list first having values A,B,C,D ..and third show number 1 to 16
my problem is i can get only those LNS signal on receiver which are directly connect to diseq 3 ... other two diseq signal not show ..
i already try below
List one "diseq 1.1"
List two "A" - here diseq 1 is connected
List three "1" - select 1 to 4 as per need
But i can not get any signal even not get strength signal
same seething wrsks fine with directly connect LNB..
I hope you understand my issue .. kindly share your contact cell or whats app if possible .. waiting your response.
Use Diseqc 8x1 in place of Diseqc 3, as i said earlier we cannot use same types in cascade ( means after an other).
Who is online
Users browsing this forum: Apple, Claude and 2 guests