Need experts opinion related diseq switch- Really Urgent Pleazz

[bilalpk]

Yes it works this way I am using one 8 pin and second 4 pin disque switch to view 10 satellites, 1st 4ft Dish with105e-Cband, 100e-Kuband, 95e Kuband, 88e-Kuband & Abs2a @ 74.5e Kuband, 2nd 2ft dish with 52e Yahsat, 42e Turksat, and 36e Eutelsat 36b all Kuband and 3rd Dish old 8ft Mesh with Paksat 38e Cband centre & 49e Yamal 202 Cband

[awan71]

Dear adnan85
In this method you have select the correct command order on your receiver such as shown in pic.

This is my SRT 2020 HD receiver's setting I am using one 8 pin DiSEq & one 4pin DiESq swithes

.
You May get some help by this diagram.

[Athart]

Yes it works this way I am using one 8 pin and second 4 pin disque switch to view 10 satellites, 1st 4ft Dish with105e-Cband, 100e-Kuband, 95e Kuband, 88e-Kuband & Abs2a @ 74.5e Kuband, 2nd 2ft dish with 52e Yahsat, 42e Turksat, and 36e Eutelsat 36b all Kuband and 3rd Dish old 8ft Mesh with Paksat 38e Cband centre & 49e Yamal 202 Cband

If you upload Diseq setting pic, then it would be great.

[awan71]

This is my Current Setting for 9 Lnbs.

Regards.

[chazer]

@Chazer Thank you so much for your reply

I am little bit confused .. i try to explain my current setting .

Dish seething..
currently i have three diseq switches 4x1 . I am using two for 8 LNB connect and other one two ports are connect with these switch and other two ports are directly connect to lnb then connect to receiver ... See attachment ..

Receiver seething..
In satellite installation session there are three list
1. if select the diseq 1.0 then below appear only one selection list which having values A,B,C,D .. every one knows this setting
2. 1. if select the diseq 1.1 then below appear two selection list first having values A,B,C,D ..and third show number 1 to 16

my problem is i can get only those LNS signal on receiver which are directly connect to diseq 3 ... other two diseq signal not show ..

i already try below

List one "diseq 1.1"
List two "A" - here diseq 1 is connected
List three "1" - select 1 to 4 as per need

But i can not get any signal even not get strength signal
same seething wrsks fine with directly connect LNB..

I hope you understand my issue .. kindly share your contact cell or whats app if possible .. waiting your response.

Use Diseqc 8x1 in place of Diseqc 3, as i said earlier we cannot use same types in cascade ( means after an other).

[Athart]

20170830_154245.jpg

This is my Current Setting for 9 Lnbs.

Regards.

Receiver se 8-pin Diseq connect kia he ya 4-pin Wala.

[awan71]

20170830_154245.jpg

This is my Current Setting for 9 Lnbs.

Regards.

Receiver se 8-pin Diseq connect kia he ya 4-pin Wala.

8 Pin DiSEq connected to Receiver.

[adnan_85]

Thanks you so much all .... I have done it with the help of you experts .

Lets conclude ..For multiple LNB we can't use 4X1 so we must need a 8X1 switch and all other 4X1switches connect to this ...


Thanks All

[kazuya1]

janab mera sawal ya hai,,,, k Dis 4 x1 pen ko dis 8.1 mein laga dia jesa ap ny bataya ... wesy karny k baad .....

For lnb 1 k lia Disq =A and Dis1.1 = 4 ok ab lnb 2 or three and four k lia b same seting required hu gi in receiver ?

or ager blind scan karny sy sab garbar nhi hu jy gi ?

[chazer]

janab mera sawal ya hai,,,, k Dis 4 x1 pen ko dis 8.1 mein laga dia jesa ap ny bataya ... wesy karny k baad .....

For lnb 1 k lia Disq =A and Dis1.1 = 4 ok ab lnb 2 or three and four k lia b same seting required hu gi in receiver ?

or ager blind scan karny sy sab garbar nhi hu jy gi ?

Yes, for Diseqc 1.0 [Diseqc 4pin] LNB2 , LNB3 and LNB4 you use same setting for Diseqc 1.1[Diseqc 8pin] witch is 4 in your case and secondly it has no conflict with blind scan.